Maintenance dosing of 0.1 - 0.25 kg weekly will keep the system operating effectively. To reactivate the plant, 1 kg Rxsol Zyme 700 FN should be mixed with 10-15 litres of hand hot (35☌) fresh water, left for 10-15 minutes (stirring periodically) for the bacteria to activate before dosing into the tank daily until the system is operating efficiently. Ineffective or septic sewage treatment can be reactivated and maintained in peak operating efficiency by dosing Rxsol Zyme 700 FN direct in the tank or via the nearest toilet. Adjust procedures and/ or applications appropriately.ĭirect dosing to the sewage treatment plant or via the nearest toilet will greatly enhance the biological activity and keep the plant at peak operating efficiency. Polishing time will be reduced and the surface will absorb less sealer. At this point the floor can be polished and/or sealed. After drying, remove any powdered residue using a stiff brush before continuing. Allow treated surfaces to dry before any additional procedures are initiated. After application surface should take minimum 5 to 10 minutes to dry if dryness occurs immediately or in 2 - 3 minutes then apply densifier again. Apply enough product to wet the surface without forming puddles. This will also help you determine the coverage that should be expected.Īpply RXSOL Densifier undiluted with lowpressure sprayer. Spray section with water to determine how absorbent the concrete is and if absorbency is consistent. Check the absorbency of each slab before proceeding.
CLEAN surface completely mainly make OIL grease, wax free, If possible before one days or Air movers can be used to shorten drying time. . Also for out side application it will not rain for several hours. Maintain Temperature of floor in between 10 degrees C and below 37 degrees C. This will neutralize any remaining acid and passivate steel surfaces. This solution should be circulated for 2-4 hours or until pH value comes 6-7. NOTE : After using RXSOL-16-1008-060 ( After completion of descaling ) rinse all equipment and metal surfaces at least one time with a 0.5% solution of RXSOL-20-2059-025 in fresh water. The process of descaling is checked by a periodical pH testing of the solution.įor silica scales and very hard scales, power and liquid forms of RXSOL-41-8865-025 is recommended.įor the prevention of further scaling in melting industry, RXSOL-41-8865-025 is recommended. If circulation of system shows constant pH 2 to 3 after time confirms the completion of the process of descaling. RXSOL-41-8865-025 dilute with fresh water as 5-30%, solution depending on scale.Make a circulation system so as to allow the solution to enter through the lowest point and leave through the highest point of the equipment, which is to be descaled.įill up the whole system with the solution and circulate through a centrifugal pump.Īt the initial stages, pH of the solution is generally at 2 to 3 there is increase in the pH of the solution, during reaction.The increase in the pH of the solution during circulation reflects on going reaction. Add more quantity of RXSOL-41-8865-025 and continue circulation, in case of the pH level being 4.5 to 5. It is the tail solvent of oil based gravure and flexographic printing ink and the based solvent of oil based screen printing ink.ĭipropylene glycol methyl ether can be used as solvent for high-grade electrophoretic paint.ĭipropylene glycol methyl ether can be used as the cleaning agent for domestic and industrial use, the remover of grease and paint, and the coupling agent and solvent of metal cleaning agent and hard surface cleaning agent.ĭipropylene glycol methyl ether is also used as the stabilizer of agricultural herbicide, flavoring agent of essence, coalescing agent of ground polishing and brightening agent, emollients used in cosmetic formulations as well as the coupling agent and solvent of some vat dye fabric.ĭipropylene glycol methyl ether is also a component of brake fluid. DIPROPYLENE GLYCOL METHYL ETHER is a solvent used in paints, pastes, dyes, resins, brake fluids and inks, and in making cosmetics.ĭipropylene glycol methyl ether is a kind of to slow volatile solvent, it can be used as the true solvent.
0 kommentar(er)
